MieleRepair Miami
(305) 518-1594 Book a visit

Twenty-five jobs, and what each one starts at

Miele repair in Miami, job by job.

Every repair we carry out on this equipment, with a starting figure and what the work involves. The figures are honest starting points and none of them is a final price: the exact cost is confirmed on site, after the diagnostic, before anything is ordered.

Book a diagnostic (305) 518-1594
  • 25 repairs with a published figure
  • from $95 diagnostic, credited to the repair
  • OEM parts available on order
  • 3 counties covered end to end

Book a visit

Book a diagnostic visit

Your model number and a line about what it is doing is enough to get started. We will confirm the earliest slot we can genuinely keep.

  • Diagnostic from $95, credited toward the repair when you go ahead
  • The work and the price in writing before anything is opened
  • A warranty on our workmanship
  • Miami-Dade, Broward and Palm Beach counties
Call (305) 518-1594
  1. 01 You tell us the model and what the unit is doing. A photo of the display helps.
  2. 02 We come back with the earliest slot we can genuinely keep, not the earliest one that sounds good.
  3. 03 Diagnosis on site, then the scope and the price in writing before anything is opened.

Your details stay private. No spam, ever.

Loading the booking form…

The booking form is taking longer than it should. Call (305) 518-1594 and we will book the visit with you.

By job

What each repair involves, and what it starts at

If you already know what the appliance needs, start here. If you do not, the appliance pages describe the symptoms and point at the right job.

  • A technician holding a multimeter and touching a probe to a terminal in the wiring behind an appliance, a work light clipped to the cabinet
    from $95

    Diagnostic visit

    One visit that ends with a named cause, a figure and a decision — and the fee comes off the bill if you go ahead with the work.

    • Credited against the repair
    • A written figure before anything is ordered
    • Nine appliance types, one rate
    What this involves
  • Hands with pliers on the corrugated dishwasher drain hose where it joins the waste spigot under a kitchen sink, a tray and a towel catching the drips
    from $175

    Dishwasher drain & fill repair

    Water not arriving, or not leaving. On a Miele this is the best-reported problem in the house — the machine names the stage it stopped at, and four of the five things it can be are outside the appliance and free to check.

    • The tap, the inlet filter and the hose checked before any part
    • Drain path proved from the tub to the standpipe
    • Flow pressure measured, not assumed
    What this involves
  • Gloved hands holding the circulation pump and its impeller housing clear of an opened dishwasher lying on its back
    from $265

    Dishwasher pump & motor repair

    Water arriving and leaving normally, and the dishes still coming out dirty. That is the circulation side — the wash motor, the diverter and the spray arms — and which rack is failing tells us which of the three before anybody arrives.

    • Diverter position identified from which rack is failing
    • Spray arms and their bearings checked before parts
    • Machine drawn out from under the counter as part of the job
    What this involves
  • A technician lifting the cylindrical flow-through heater and its hose out of the base of a dishwasher laid on its back on a mat
    from $225

    Dishwasher heating & drying repair

    Water that never gets hot, or dishes that come out wet. On this make the heater and its temperature sensor report as two separate conditions, which is why this is its own repair rather than part of the pump one.

    • Heater and sensor tested separately, as the machine reports them
    • Drying checked before anything is called a failure
    • Rinse aid and door-opening behavior confirmed first
    What this involves
  • Gloved hands pressing a new rubber tub seal into the channel around the mouth of a dishwasher, the old seal coiled on the open door
    from $165

    Dishwasher door & seal repair

    The cheapest thing that goes wrong on the appliance and the one people live with longest: a door that drops, a door that will not stay shut, or a seal gone hard enough to let steam past. On a fully integrated machine the door is carrying your cabinetry, which is why it wears faster here.

    • Springs and hinge cables checked as a pair
    • Panel weight accounted for on integrated machines
    • Seal replaced along its whole run, not patched
    What this involves
  • A technician holding the drain pump clear of the open plinth of a washing machine by torchlight, the impeller wound with hair and thread
    from $195

    Washing machine drain & pump repair

    A cycle that stops with water in the drum, or a machine that will not empty at the end. The W1 machines report the water path in detail, so the diagnosis is usually short — what lengthens the visit is getting to the back of a machine in a closet.

    • Drain filter and pump checked before any part is ordered
    • Pressure system tested, not assumed
    • Machine drawn out and put back level
    What this involves
  • A technician driving a new bearing into the tub half of a washing machine with a drift and a mallet on a workshop bench, the old bearing and seal beside it
    from $425

    Washing machine bearing & drum repair

    The top of the laundry list, and the one repair on this site where the honest answer is sometimes no. On a machine built to last twenty years a bearing at ten is worth doing; on one that has had it done before, usually not — and you get told which.

    • Noise diagnosed before anything is quoted
    • The straight answer on whether it is worth doing
    • Drum and bearings replaced as an assembly where that is correct
    What this involves
  • A hand withdrawing the door interlock from the front panel of a washing machine, its wiring loom still attached, pliers in the other hand
    from $215

    Washing machine door & lock repair

    A door that will not lock, or one that will not let go. Miele prints both of these in words on the display as well as as a number, which is unusual for this maker — and a locked door with a wet load behind it is treated as a same-day call rather than a scheduled one.

    • Same-day where the schedule allows, with a load inside
    • Door opened without damaging the interlock
    • Hinge and catch alignment checked with the lock
    What this involves
  • A gloved hand fitting a service gauge line to the sealed refrigerant circuit of a heat-pump dryer opened on a workshop bench
    from $345

    Dryer heat pump & sensor repair

    A ventless dryer has no heating element to replace. It has a sealed refrigerant circuit, and twenty-four of the twenty-eight conditions Miele publishes for its dryers point into it — which is the shape of the machine rather than a sign that yours is unusual.

    • The owner-serviceable half eliminated first, at no charge
    • Sealed circuit tested rather than swapped
    • Sensors read as resistances, not guessed
    What this involves
  • Two hands drawing the clear condensate container out of the top of a heat-pump dryer, water visible in it
    from $135

    Dryer condensate & filter service

    Priced as maintenance on purpose, because on a ventless dryer in this humidity it is the row that keeps the expensive one away. Filters, condenser block, condensate path and the sensors that all three affect.

    • Both filters and the condenser block cleaned properly
    • Condensate container, float and pump checked
    • Drum sensors cleaned so the cycle ends when it should
    What this involves
  • Two hands lifting the ring element clear of the fan at the back of an oven cavity, the fan cover removed
    from $195

    Oven element & sensor repair

    An oven that will not reach temperature, will not hold it, or is simply wrong by a consistent amount. The element and the sensor produce complaints that sound identical in the kitchen and cost very different amounts.

    • Temperature measured at the shelf, not read off the panel
    • Sensor and element tested separately
    • Access into a tall housing planned rather than improvised
    What this involves
  • A gloved hand freeing the door latch mechanism in the top frame of a built-in oven, its motor and spring exposed, the door hanging open below
    from $215

    Oven door latch repair

    An oven that has stopped part-way through a self-clean holds its door shut deliberately. When it will not release as the cavity cools, that is the latch — and it is a same-day call, because forcing it is how a latch becomes a door.

    • Same-day where the schedule allows
    • Door released without damaging the mechanism
    • The cause of the interrupted cycle found, not just the latch
    What this involves
  • Descaling solution being poured from a plain jug into the water container of a built-in steam oven standing on the worktop, the oven door open behind
    from $145

    Steam oven descaling

    The most useful row on this site, and it is maintenance. A combi-steam oven calculates its descaling interval from a water hardness figure set at the factory — a figure South Florida water exceeds — so the reminder arrives after the scale does.

    • Nozzle and generator descaled, not just the reminder cleared
    • Water hardness set on the appliance so the next interval is right
    • The whole water path flushed afterwards
    What this involves
  • Gloved hands lifting the steam generator out of a built-in steam oven, its boiler cylinder crusted white with scale
    from $235

    Steam oven water system repair

    The steam side has a set of conditions entirely its own: the intake valve, the nozzle, the container, the suction hose inside it — and the conductivity of the water, which is a real published cause and catches every house with an osmosis system.

    • Five published causes worked through in the maker's own order
    • Osmosis systems checked as a cause, not dismissed
    • Nozzle and pump proved separately
    What this involves
  • A technician lifting the brass burner cap off a sealed burner on a stainless rangetop and clearing the injector with a fine wire
    from $225

    Range & rangetop repair

    Two appliances sharing a cabinet, and on this make two separate boards. Which half is reporting — the cooking surface or the oven cavity — is the first thing a visit establishes, and saying it on the phone changes what comes on the van.

    • The two halves diagnosed separately, as the appliance reports them
    • Gas conversion and regulator setting handled properly
    • Slide-in appliance drawn out from between stone
    What this involves
  • A technician unplugging a connector on the underside of an induction cooktop tilted up on blocks over the worktop, its copper coils and power board exposed
    from $245

    Induction cooktop repair

    The surface that reports the most on this make, and the one most often misread. A zone that switches itself off is usually the overheating protection doing its job — and in a South Florida island the reason is frequently that there is no air under the appliance.

    • Overheating causes ruled out before any part is quoted
    • Ventilation under the appliance checked as a real cause
    • Generator and touch board tested separately
    What this involves
  • Two pairs of gloved hands lifting a black glass cooktop out of its worktop cut-out on suction pads, the frame and wiring loom exposed below
    from $395

    Cooktop glass replacement

    Cracked, chipped at the edge, or crazed around a zone. The surface is most of the cost and it is specific to the model — so availability is confirmed before anything is booked, because on a discontinued top it sometimes decides against the repair.

    • Availability confirmed against the model number first
    • Appliance made safe the same day where it is cracked through
    • Frame and seal renewed with the glass
    What this involves
  • A gloved hand playing a steam nozzle over the iced evaporator coil behind the removed back panel of a freezer, a folded towel below
    from $225

    Refrigerator cooling & defrost repair

    Where most refrigeration calls actually land. Fans, defrost circuits, dampers and sensors — and, ahead of all of them, a condenser nobody has cleaned, which imitates every one and frequently costs the visit and nothing else.

    • The condenser first, always
    • Sensors read rather than swapped
    • Sealed system excluded before it is ever mentioned
    What this involves
  • A technician holding a refrigeration gauge manifold with its red and blue hoses connected to the compressor bay of a refrigerator, a vacuum pump standing on the floor
    from $495

    Refrigerator sealed system repair

    The largest figure on this site, and the one reached last. A compressor or a leak is what remains after the condenser, the fans, the defrost circuit, the dampers, the sensors and the seals have each been excluded — every one of which produces the same complaint for a fraction as much.

    • Only quoted after everything cheaper is excluded
    • The straight answer on whether the cabinet is worth it
    • Recovery and recharge done properly, not topped up
    What this involves
  • A technician adjusting the concealed hinge of an integrated refrigerator, its furniture panel door held open on the lit interior of shelves and drawers
    from $165

    Refrigerator door & panel alignment

    A panel-ready door is carrying your cabinetry, and cabinetry is heavy. Over time it settles, and a door standing a fraction open in this humidity is not a cosmetic problem — it is frost on the evaporator and a cabinet that never stops running.

    • Doors set with the panels on, not before
    • Seals checked along their whole run
    • Pairs of columns aligned to each other as well as to the room
    What this involves
  • A technician kneeling at an undercounter wine cabinet with two wooden shelves drawn out, working on the fan at the back of the compartment by torchlight
    from $215

    Wine refrigerator repair

    A cabinet with a stricter job than cold: hold a temperature steadily, hold humidity with it, and do neither loudly. A single wrong zone is good news diagnostically — it rules out the compressor and the condenser immediately.

    • Zone-by-zone diagnosis before any major part
    • Level and airflow checked as real causes
    • Door seal and glass treated as thermal parts
    What this involves
  • A technician on a step ladder reaching into the open canopy of a stainless range hood, one grease filter hanging down beside the blower
    from $165

    Range hood repair

    The cheap end of the list, honestly. A hum without rotation is usually a capacitor; where the ventilator actually lives — inside the hood, in the ceiling or on the roof — decides the labor and is not visible from the kitchen.

    • Capacitor tested before any motor is quoted
    • Remote and in-line ventilators traced, not assumed
    • Filters and lamps done on the same visit
    What this involves
  • A technician crouched at the open service panel of a stainless commercial washing machine in a block-walled utility room, meter probes on the terminal block
    from $245

    Commercial appliance repair

    The Little Giants washers and dryers, the PFD professional dishwashers and the ironers behind them. The engineering is the same as the domestic machines and the appointment is not: this equipment runs all day, and being down costs money by the hour.

    • Looked at around your hours, not around a kitchen's
    • Parts ordered against a machine that cannot wait
    • A way to keep running where there safely is one
    What this involves
  • A technician brushing the condenser coil behind the removed plinth grille of a built-in refrigerator, vacuum hose and folded mat on the floor
    from $145

    Appliance maintenance

    One visit covering every condenser, filter, descale and seal in the kitchen and the laundry room. In a full Miele household that can be six appliances, and doing them together is meaningfully cheaper than three separate visits.

    • Every appliance in the house on one trip
    • The three things this climate is hard on, all in one visit
    • Water hardness set so the appliances count correctly
    What this involves
  • Two technicians on their knees easing an integrated dishwasher into its cabinet opening, one holding the oak door panel while the other guides the hoses
    from $225

    Appliance installation

    Where a meaningful share of the repairs on this site are prevented or created. Ventilation under an induction cooktop, a drain that will actually take a heat-pump dryer, and water at the pressure the maker names as a minimum.

    • Ventilation, drainage and flow pressure checked, not assumed
    • Panel-ready doors hung and set with the panels on
    • Levelling done properly, on every machine
    What this involves

Three rows that exist to prevent the others

Descaling, a dryer service and a clean condenser are the cheapest things on this list.

They are also the three that keep the expensive rows away, and on this make in this city they are not optional maintenance. A combi-steam oven works out its descaling interval from a water-hardness figure set at the factory, and the supply across Miami-Dade, Broward and Palm Beach is harder than that figure — so the reminder arrives after the scale does, and the steam generator pays for it.

The same shape twice more. A ventless dryer whose condenser block is packed runs long cycles at higher load for years before it complains, and the compressor is what wears. A refrigeration condenser coated in damp dust imitates every cooling failure on this site and is not a part at all. All three are on the maintenance page and all three cost less than what they prevent.

Appliance maintenance
A glass jug of solution, a plain descaling tablet on a folded cloth, and the water container drawn out of a built-in steam oven

Most of these are not an owner's job, and the maker says so

Where the manufacturer says stop, this site stops too.

Of the conditions Miele publishes for the appliances on this site, a clear majority carry the sentence that they cannot be remedied by the owner. We repeat that rather than working around it: those pages carry no invented checklist and no ten-step routine that ends in booking a visit anyway.

The rest do have steps, and they are the manufacturer’s own. A tap that is not fully open. An inlet filter thick with scale. A condensate container that needed emptying. A cooktop with no air under it. Every one of those genuinely ends a call for the price of the visit, and several of them end it for nothing at all — which is why the code archive on this site is free to read before you book anything.

Look up what your appliance is showing
A canvas tool roll opened flat on a worktop with nut drivers, a work light, a meter and a pair of gloves laid out beside it

By appliance

Not sure which job it is?

Start from the appliance instead. Each page lists what goes wrong with it and links to the repair.

  • A fully integrated dishwasher standing open on a light floor, its stainless tub and detergent dispenser in view
    Fully integrated · Semi-integrated · Built-under · ADA · AutoDos · 18" and 24"

    Dishwashers

    The appliance this name means in most American kitchens, and the one that tells you the most about itself. A Miele dishwasher reports the water path in detail — the tap, the inlet filter, the hose, the drain — which is why more of these calls end without a part than on any other appliance in the house.

    Dishwasher repair
  • A hand pushing a white towel past the door seal into a washing machine drum
    W1 front-loading · TwinDos · CapDosing · 24" · 120V

    Washing machines

    A small line and a deep one: Miele sells three washing machines in the United States and builds all of them to a twenty-year design life. That changes the repair question — on a machine this age, the honest answer is usually which single part has worn rather than whether the machine is finished.

    Washing machine repair
  • A tumble dryer standing open, the perforated stainless drum and its vanes lit from the door
    T1 heat pump · Ventless · 24" · 120V · No duct required

    Heat-pump dryers

    Every dryer Miele sells in the United States is a heat pump, and there is no vented model to compare it to. That is the single most useful thing to know before booking: this machine has a sealed refrigerant circuit rather than a heating element, so almost nothing that goes wrong with it is what goes wrong with an ordinary dryer.

    Dryer repair
  • The control fascia of a stainless range: a row of knurled knobs, program symbols and a blue clock
    HR dual fuel · HR induction · 30", 36", 48" · Gas and LP

    Ranges

    Two appliances on one chassis, and on this make they report separately. The cooking surface and the oven cavity are different boards, so the first thing worth establishing is which half is unwell — it changes the parts, the access and the figure.

    Range repair
  • A black induction cooktop with its touch control strip lit, a pan of stuffed peppers on the ring
    KM induction · KM gas · KM electric · KMR rangetops · 24" to 48"

    Cooktops and rangetops

    The one place this make writes something other than F and a number: the induction tops write FE, and a bare F with nothing after it is its own condition. Induction also reports more than any other cooking surface Miele builds — and most of what it reports is about heat and about the glass rather than about a part.

    Cooktop repair
  • A built-in oven standing open on an enamelled cavity, the fan cover at the back, a tray on the lowest runner
    H wall ovens · DGC combi-steam · Speed ovens · Warming and vacuum drawers

    Ovens, steam ovens and drawers

    One control family covers the wall ovens, the combi-steam ovens, the speed ovens and the drawers, which is why they share a page. The steam side adds a set of conditions all its own — about the intake valve, the nozzle, the container, and the hardness of the water itself.

    Oven repair
  • The lit interior of a tall refrigerator column, fruit and salad on glass shelves and a crisper drawer below
    MasterCool columns · Built-in bottom mounts · Built-in freezers · Panel-ready

    Refrigeration

    MasterCool columns and built-in cabinets, most of them behind your own panels. What is distinctive about their conditions is that the cabinet usually keeps running while it reports: it is telling you a reading has stopped making sense, not that it has stopped cooling — so there is normally time to act rather than to empty it.

    Refrigerator repair
  • A built-in wine cabinet standing open in dark cabinetry, bottles lying on lit wooden shelves
    KWT built-under · MasterCool wine · Multi-zone · Panel-ready

    Wine refrigerators

    A cabinet with a job that is stricter than cold: hold a temperature steadily, hold humidity with it, and do neither of those things loudly. Zone count and access decide most of what a repair costs here, and a single wrong zone rules out the compressor immediately.

    Wine refrigerator repair
  • An on-premise laundry: white professional washers and dryers along a tiled room, a linen cart of white sheets being wheeled past
    Little Giants PWM and PDR · PFD professional dishwashers · Rotary ironers

    Commercial and professional

    The line Miele builds for places that are open for business: the Little Giants washers and dryers, the PFD professional dishwashers, and the ironers behind them. Same engineering, a different appointment — this equipment runs all day, and being down costs money by the hour.

    Commercial appliance repair
See every appliance

How a figure on this site is arrived at

What is in the number, and what is not

Every figure here is a "from". Three things decide where inside the range a particular job lands.

What is included

  • Parts and labor together, unless the page says otherwise
  • The diagnostic fee, credited when you go ahead with the work
  • A written figure agreed before anything is ordered

What moves it

  • Access — a fully integrated machine under stone, a wall oven at eye level, a washer in a closet
  • Which part it turns out to be: a sensor and the circuit it watches are the same complaint
  • Whether the part is current or has to be sourced for a discontinued model

What is never in it

  • A final price before an on-site diagnostic — we do not publish one
  • Anything you can do yourself, which we will tell you about instead of charging for
  • A brand premium. Where a job costs the same on this equipment as on any other, it is published at that figure

Not seeing your repair?

Twenty-five rows is not the limit of what we will look at.

The list above is what we publish a figure for. It is not the whole of what we do: a ventilation hood, a warming drawer, a vacuum-sealing drawer, a built-in microwave, a downdraft, a ceiling extractor, a rotary ironer in a laundry room — all of them are in scope even where there is no row here with their name on it.

If what your appliance is doing is not on this list, describe it in your own words. Call (305) 518-1594 or use the form above, and you will get a straight answer about whether it is something we handle before anybody is booked.

Call (305) 518-1594 Describe it in the form

Before you book

Questions about the work and the figures

Why is there no exact figure published for anything?

Because a price given before the appliance has been looked at is a guess, and the ones that turn out to be wrong are wrong in the customer's direction. Every figure here is a starting point; the exact cost is confirmed on site after the diagnostic and agreed in writing before anything is ordered.

Is the diagnostic fee really credited?

Yes, against the repair when you go ahead. It is a rate for the time and the travel rather than a charge for saying yes.

Do you guarantee the work?

We warrant our own workmanship and the parts we fit — the work we performed and the components we supplied. That is our own guarantee rather than the manufacturer's, and repairs still covered by the maker go through its own service network rather than through us.

Are you Miele?

No. We are an independent appliance repair company and we are not affiliated with, authorized by or endorsed by any manufacturer. Brand names and model numbers are used for identification only and belong to their owners. If your appliance is still inside the manufacturer's coverage, using that first is usually the right advice and you will get it.

Do you use original parts?

OEM parts are available on order and are what we fit unless you ask otherwise and there is a sound equivalent. On this equipment it matters more than average, because a good deal of it is model-specific.

Tell us what the appliance is doing.

You will get a starting figure on the phone and a firm one before any work begins.

Schedule a visit Call (305) 518-1594

This article is based on:

  • Official manufacturer documentation
  • Internal repair procedures
  • Technician repair history
  • Company quality standards
Call (305) 518-1594